Commercial Floors
Armor Garage Flooring coats shop floors, warehouses, service bays and showrooms. Working floors get a sand-finish epoxy system matched to their traffic and spills.
Learn More
Quartz floor coatings from Armor Garage Flooring put colored quartz granules into the coating itself. We grind the concrete first. Then quartz is broadcast into a wet coat, twice, and a clear topcoat seals it. The trade calls that a double broadcast. The result is one continuous floor with a fine, sand-like texture and color across the whole surface.
Quartz is our system for floors that work hard and get wet. We install quartz floors for restaurants, commercial kitchens and other businesses around Eagle Lake and across Polk County. It goes outdoors too, on pool decks and driveways. You choose from 30 quartz colors on our flake and quartz colors page. Call or text (866) 282-7667 for a free estimate.
Tell us about the floor, how it is used and where it is. We look at the job and put your free estimate in writing.
Every quartz floor starts with prep. We grind the concrete to take off the weak top layer and any old sealer. Cracks are filled, and the slab is tested for moisture. A moisture-blocking primer goes down first when the slab calls for one.
Then the floor is built in layers. A base coat goes down, and colored quartz is broadcast into it until the coat will not take any more. The loose quartz is swept off. A second coat and a second broadcast follow, and a clear topcoat seals the floor. One manufacturer's quartz system sheet puts the finished system at about an eighth of an inch thick.
Quartz is a mineral, not a vinyl chip. A coating manufacturer's own comparison says quartz is harder than vinyl flake. The maker of the quartz adds that flake and quartz bring the color and the texture, while the resistance comes from the coating around them. So the coating system matters as much as the quartz.
Start with restaurants and commercial kitchens. Florida's Division of Hotels and Restaurants says floors in food preparation, dishwashing and bathroom areas must be smooth, easy to clean and non-absorbent. The FDA Food Code that the state adopts makes an exception to smooth for floor finishes that add traction. A quartz floor is one continuous surface, so there are no grout lines to scrub. Your plan review and your inspector have the final word on any floor, so check with the Division before you choose a finish.
The system is made for wet rooms. One manufacturer's quartz system sheet lists food prep areas, commercial bakeries, restrooms, locker rooms and shower areas among its typical uses. The same sheet says the floor suits frequent cleaning and washdown. Quartz also works on a shop or showroom floor where you want color in a textured finish.
Quartz goes outdoors too. The same manufacturer's color-stable quartz system sheet lists exterior environments, and its catalog lists pool decks and walkways for the quartz system. The maker of the quartz says it suits outdoor use and advises against bold, bright colors there, since they can fade early. A quartz floor costs more than a flake floor, so most garages get flake.
A new kitchen floor means downtime, so plan the days. One manufacturer's two quartz system sheets list light foot traffic after 24 hours and heavy traffic after 48 or 72 hours, depending on the resin. Full cure takes from two days to a week. Your floor follows the schedule of the coating that goes on it.
Central Florida weather is part of the plan. NOAA climate normals put summer dew points across the region in the low 70s. Coating sheets call for a slab at least 5 degrees Fahrenheit above the dew point. Slab temperature, humidity and dew point get checked before any coating goes down.
Tell us how the floor is used. One quartz system sheet says the system is not designed for continuous thermal shock, so we ask about hot water washdowns and what gets spilled. The sheet also says it is not a waterproofing system. We look at kitchens and other commercial floors in Eagle Lake, Winter Haven, Lakeland and the rest of our service area.
Call or text for a written quote. We work about 45 miles around Eagle Lake across Polk County and Four Corners.
(866) 282-7667From the first call or text to the finished work, here is how it goes.
Call or text (866) 282-7667, or send the form. Tell us which floor you want coated and the town it is in.
We look at the concrete, including cracks and any old sealer or coating. Then we recommend the system that fits.
Your free estimate comes in writing, with the work and the price spelled out. Once you say yes, we set a start date.
We grind the whole slab and fill the cracks before any coating goes on.
A base coat goes down, then the flake or the sand, then a topcoat. The coating manufacturer's schedule sets when you can walk on it and park on it.
Common questions about quartz floors around Eagle Lake and the rest of Polk County. If yours is not here, call or text and ask.
Armor Garage Flooring coats shop floors, warehouses, service bays and showrooms. Working floors get a sand-finish epoxy system matched to their traffic and spills.
Learn More
We coat the concrete deck around a pool with a sand or quartz finish. The texture gives the deck grip when it is wet, and a clear, UV-stable topcoat seals it.
Learn More
Our epoxy system goes over concrete we grind first and ends in a sand finish for grip. It suits workshops, utility and laundry rooms, basements and commercial floors.
Learn MorePolyaspartic full flake goes on garages, with a UV-stable topcoat. Epoxy with a sand finish goes on shop floors and workshops.
Every job starts with a look at the floor. Your free estimate then spells out the system and the price in writing.
Tell us about the floor you want coated and where the property is. Call or text (866) 282-7667 or use the form, and we will set up your free estimate.
Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.