Pool Deck Coatings
We coat the concrete deck around a pool with a sand or quartz finish. The texture gives the deck grip when it is wet, and a clear, UV-stable topcoat seals it.
Learn More
Armor Garage Flooring installs patio coatings in Eagle Lake and across Polk County. We coat back patios, lanais, screened porches and walkways. The prep matches our garage floor coatings in Eagle Lake: we grind the concrete before any coating goes down.
Outdoor slabs face hard sun and summer storms. A textured flake or sand finish gives grip when the slab is wet. A clear, UV-stable topcoat from our polyaspartic floor coatings seals it. Call or text (866) 282-7667 for a free estimate.
Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.
Our patio coatings go on poured concrete, including the lanai slab under a screen enclosure. Walkway coatings go on the path to the front door and the entry slab. The driveway itself falls under concrete driveway coatings, and the deck around a pool falls under pool deck coatings.
Every job starts with prep. We grind the concrete so the coating can bond to it. Cracks are filled before the first coat, though a crack that moves can show again.
The coating then goes on in layers. A base coat goes down, and flake or sand is broadcast into it for texture. The loose excess is scraped and swept off before a clear topcoat seals the surface.
Epoxy has a weak spot outdoors. Coating makers' own data sheets say it can yellow and turn chalky in direct sun. Data sheets for polyaspartic rate it UV-stable. For a patio in full sun, a polyaspartic topcoat is the better fit.
A covered lanai or screened porch sees less direct sun than an open patio. Its slab still sits on the ground, so the moisture test matters there too.
Color is part of the choice too. The flake manufacturer advises against bold, bright colors outdoors, since they can fade early. Our flake floor coatings come in multiple blends, and a muted blend suits a slab in full sun.
The nearest NOAA station, in Lakeland, averages about 83 days a year with a tenth of an inch of rain or more. Most of the rain falls from June to September. One polyaspartic data sheet says to keep a fresh coat away from water and condensation for its first 24 hours. So the forecast matters on an outdoor job.
Summer dew points across Central Florida run in the low 70s. Coating makers want the slab at least 5 degrees above the dew point, so the surface stays dry. We check slab temperature and dew point before the coating goes down.
Under a lanai roof or out in the open, moisture also rises from the ground. Polk County's largest soil map unit is Smyrna and Myakka fine sands, and Myakka is Florida's state soil. NRCS puts their water table less than 18 inches down for 1 to 4 months in most years. So the slab is tested for moisture first, and a moisture-blocking primer goes down if the test calls for one.
Call or text for a written quote. We work about 45 miles around Eagle Lake across Polk County and Four Corners.
(866) 282-7667From the first call or text to the finished work, here is how it goes.
Call or text (866) 282-7667, or send the form. Tell us which floor you want coated and the town it is in.
We look at the concrete, including cracks and any old sealer or coating. Then we recommend the system that fits.
Your free estimate comes in writing, with the work and the price spelled out. Once you say yes, we set a start date.
We grind the whole slab and fill the cracks before any coating goes on.
A base coat goes down, then the flake or the sand, then a topcoat. The coating manufacturer's schedule sets when you can walk on it and park on it.
Common questions about patio coatings around Eagle Lake and the rest of Polk County. If yours is not here, call or text and ask.
We coat the concrete deck around a pool with a sand or quartz finish. The texture gives the deck grip when it is wet, and a clear, UV-stable topcoat seals it.
Learn More
Armor Garage Flooring coats shop floors, warehouses, service bays and showrooms. Working floors get a sand-finish epoxy system matched to their traffic and spills.
Learn More
Our main garage floor system pairs a polyaspartic coating with a full flake broadcast. It cures fast and holds its color in the sun.
Learn MorePolyaspartic full flake goes on garages, with a UV-stable topcoat. Epoxy with a sand finish goes on shop floors and workshops.
Every job starts with a look at the floor. Your free estimate then spells out the system and the price in writing.
Tell us about the floor you want coated and where the property is. Call or text (866) 282-7667 or use the form, and we will set up your free estimate.
Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.