Patio Coatings
We coat patios, lanais, screened porches and walkways around Eagle Lake and Polk County. A textured flake or sand finish gives the slab grip when it is wet.
Learn More
Driveway coatings from Armor Garage Flooring cover the concrete you drive and park on every day. That includes the driveway and the slabs tied to it, like the approach at the street and the front entry. We grind the concrete and fill the cracks first. Then we build a polyaspartic flake coating with a clear, UV-stable topcoat and a textured finish for wet grip.
We coat driveways for homeowners in Eagle Lake and across Polk County and the Four Corners side of Central Florida. Our customers include new homeowners in new-construction communities. Driveways get the same polyaspartic system as our garage floor coatings in Eagle Lake, with a finish chosen for weather. Call or text (866) 282-7667 for a free estimate.
Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.
A driveway sits in the open and takes far more sun than a garage floor. Epoxy is the system we use on interior floors like shops and utility rooms. Outdoors, epoxy makers' own data sheets warn that it can yellow and chalk under long sun exposure.
Our driveway coatings use the polyaspartic floor coating system instead, with a clear topcoat. Polyaspartic data sheets list it as UV-stable and resistant to yellowing. The flake manufacturer advises against bold, bright colors outdoors, since they can fade early. Softer tones from our full flake color blends suit a sunny driveway.
Heat matters on install day too. NOAA's climate normals for Lakeland, the nearest weather station, show about 119 days a year at 90 degrees or more. One polyaspartic data sheet says its working time is much shorter above 90 degrees. Slab temperature and dew point get checked before the coating goes down.
A coating bonds to the concrete under it. One manufacturer's system sheet calls for sound, structurally stable concrete. A driveway that heaves or crumbles needs concrete repair first, and that is a separate trade. These systems are made for concrete, so asphalt and paver driveways are not candidates.
Cracks and chipped spots get filled as part of our prep. A crack that still moves can show through again, since a coating is not a structural repair. Control joints, the straight grooves in a driveway, can be filled or coated into and back out.
We grind the concrete to take off the weak top layer and any old sealer. Oil that soaks deep into a driveway can weaken the bond, and grinding alone does not always reach it. For a newly poured driveway, coating data sheets call for 28 to 30 days of cure before the first coat.
NOAA's normals for Lakeland, the nearest weather station, show about 57 inches of rain a year. About 60 percent of it falls from June through September. A polyaspartic data sheet calls for protection from water and condensation during the first 24 hours of cure. A driveway coating needs dry weather after it goes down, so the forecast matters.
Water also rises from below. NRCS soil data shows a seasonal water table within 18 inches of the surface under about half of Lakeland's land. The ready-mixed concrete industry's trade association says the soil under a slab stays damp, wherever the house sits. Coating makers call for a moisture test first, and a moisture-blocking primer when the reading runs high.
Walk-on and drive-on times follow the coating manufacturer's schedule. Polyaspartic data sheets put foot traffic at a few hours to a day, and cars at a day or more. Full cure takes one or two days on some products and up to a week on others.
Call or text for a written quote. We work about 45 miles around Eagle Lake across Polk County and Four Corners.
(866) 282-7667From the first call or text to the finished work, here is how it goes.
Call or text (866) 282-7667, or send the form. Tell us which floor you want coated and the town it is in.
We look at the concrete, including cracks and any old sealer or coating. Then we recommend the system that fits.
Your free estimate comes in writing, with the work and the price spelled out. Once you say yes, we set a start date.
We grind the whole slab and fill the cracks before any coating goes on.
A base coat goes down, then the flake or the sand, then a topcoat. The coating manufacturer's schedule sets when you can walk on it and park on it.
Common questions about driveway coatings around Eagle Lake and the rest of Polk County. If yours is not here, call or text and ask.
We coat patios, lanais, screened porches and walkways around Eagle Lake and Polk County. A textured flake or sand finish gives the slab grip when it is wet.
Learn More
We coat the concrete deck around a pool with a sand or quartz finish. The texture gives the deck grip when it is wet, and a clear, UV-stable topcoat seals it.
Learn More
Armor Garage Flooring coats shop floors, warehouses, service bays and showrooms. Working floors get a sand-finish epoxy system matched to their traffic and spills.
Learn MorePolyaspartic full flake goes on garages, with a UV-stable topcoat. Epoxy with a sand finish goes on shop floors and workshops.
Every job starts with a look at the floor. Your free estimate then spells out the system and the price in writing.
Tell us about the floor you want coated and where the property is. Call or text (866) 282-7667 or use the form, and we will set up your free estimate.
Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.