Garage floor coatings for homes and businesses across Polk CountyGarage floor coatings in Eagle Lake, FL
Armor Garage Flooring
Gray full flake garage floor with a black sports car parked on it, polyurea vs polyaspartic coatings
Call (866) 282-7667 Request a Quote

Polyurea vs Polyaspartic: Which Is Better for a Garage Floor?

In a good garage floor system, polyurea and polyaspartic are partners more than rivals. Polyaspartic is itself a type of polyurea, an aliphatic one. A common modern system uses both: a polyurea base coat, a full flake broadcast, then a clear polyaspartic topcoat. Some systems swap in a hybrid base coat. One national cost guide describes the pairing as a base coat of polyurea and a top coat of polyaspartic.

Armor Plus and Armor Signature follow this build. Armor Plus uses a polyurea base coat, a full flake broadcast to rejection and a clear polyaspartic topcoat. Armor Signature uses a hybrid epoxy/polyurea system that provides moisture mitigation, under the same full broadcast and clear topcoat. Our page on polyurea floor coatings covers both.

What is the difference between polyurea and polyaspartic?

Both are polyureas. A polyurea forms when an isocyanate reacts with a resin blend. The polyurea trade association’s definition says that isocyanate can be aromatic or aliphatic.

Pure polyurea reacts fast. A trade column gives it a pot life of about 3 seconds. The two parts mix at the spray tip of high-pressure equipment. Polyaspartic is the slower member of the family. The same column calls it a polyaspartic aliphatic polyurea.

PolyureaPolyaspartic
ChemistryAromatic or aliphatic polyureaAliphatic polyurea
In UV lightAromatic types fade or change colorData sheets list it as UV-stable
SpeedSpray polyurea: pot life of about 3 secondsPot life of 5 to 120 minutes, by product
How it goes downPure polyurea by spray rig; floor base coats by squeegee and rollerBrush, squeegee or roller
Stretch (one maker’s flake systems, same test)65 percent elongation10 percent elongation
Usual job in a garage systemBase coat, for its grip on the concreteTopcoat, for an abrasion-resistant finish

Why does aromatic polyurea yellow in the Florida sun?

Aromatic polyurea has long been the workhorse type, and color is its weak spot. A paper from the polyurea trade association’s conference says aromatic polyurea will fade or change color in ultraviolet light. It calls that a surface effect. Even so, light colors discolor and fade outdoors over time.

Aliphatic polyurea, the family polyaspartic belongs to, has excellent resistance to UV breakdown, the same paper says. So the clear polyaspartic layer goes on top, where sun through an open garage door lands. A trade column describes a bridge with a polyurea primer under a polyaspartic top coat. That top coat prevented UV degradation of the polyurea. Our polyaspartic floor coatings page covers the topcoat side.

Which one cures faster, polyurea or polyaspartic?

Spray polyurea wins on raw speed. The trade association paper puts its dry time at typically less than 30 seconds.

Floor products react slower, so an installer can spread them and broadcast the flake. One polyurea flake system sheet says to broadcast to rejection after 10 to 15 minutes, depending on temperature. Polyaspartic gives a short window too. One sheet lists about 10 to 15 minutes of usable working time, and heat shortens these windows.

Cure runs on a different clock. That polyurea flake system lists light foot traffic at 12 hours and heavy traffic at 48. Full cure takes 5 to 7 days.

Which one is more flexible, and which one bonds better?

Polyurea stretches more. One coating maker publishes sheets for two flake systems with the same clear topcoat. One sits on a polyurea base coat, the other on a polyaspartic base coat. On the same test, it lists 65 percent elongation for the polyurea system and 10 percent for the polyaspartic one.

The maker says the polyurea system handles low to moderate movement, which helps reduce cracking and delamination.

The bond starts with prep. A national cost guide credits the polyurea base coat with high adhesive strength. The polyurea system sheet ties its strong adhesion to properly prepared concrete. A trade column says acid etching is not recommended, since it adds moisture to the concrete. We grind the concrete before any coat goes down.

Which one handles hot tire pickup?

Hot tire pickup happens when tires, warm from a drive, grip the coating as they cool and pull it up. A resin flooring maker’s help page describes it on epoxy floors. It blames poor prep, such as the wrong primer or skipped grinding.

In a two-coat system, the tires ride on the topcoat while the base coat holds the bond. Our floors are made to resist hot tire pickup, and that starts with ground concrete. Staining is a separate issue. One polyaspartic sheet warns that high performance soft tires may stain the finish.

What does moisture in a Florida slab mean for each one?

Neither chemistry fixes a damp slab by itself. That maker’s two flake systems both tolerate 3 pounds of moisture vapor per 1,000 square feet in 24 hours. Above that, the polyurea sheet calls for a moisture primer first. A trade column reports polyaspartic floors failing when moisture vapor emission ran too high.

Ground water adds to it. NRCS describes Smyrna sand, a soil of large extent in peninsular Florida, on nearly level flatwoods. Its water table sits less than 18 inches down for 1 to 4 months in most years.

That is why a moisture test belongs before any coating. The polyurea system sheet recommends a calcium chloride test and in-slab relative humidity testing. A moisture primer raises the limit. One polyaspartic sheet limits its coating to under 4 pounds. Its epoxy moisture barrier primer is rated for up to 25.

Armor Signature uses a hybrid epoxy/polyurea system that provides moisture mitigation. For the epoxy side of this story, see our guide to polyaspartic vs epoxy garage floors.

How much do polyurea and polyaspartic floors cost?

One national cost guide, last updated in January 2024, puts polyaspartic floor coating at $4 to $9 per square foot. By its math, that is about $1,440 to $3,240 for an average-size garage. It adds that a moisture barrier, when required, could cost an extra $1 per square foot.

These are market numbers, not our price list. Your floor’s size and condition move the price, and so does any moisture work.

What should you ask when a quote says “polyurea” or “one day”?

A trade column says a polyaspartic garage floor can be completed start to finish in about 5 hours. The same column reports failures over slabs with too much moisture vapor. Ask these before you sign:

  • Is the base coat polyurea, polyaspartic, epoxy or a hybrid?
  • If it is polyurea, is it aromatic or aliphatic, and what clear coat goes over it?
  • Will the concrete be ground before the first coat?
  • Will the slab be tested for moisture, and what happens if the reading runs high?
  • Is the flake a full broadcast to rejection or a partial one?
  • When can I walk on the floor, and when can I park on it?

The answer to the last one should come from the product’s own cure schedule.

Which system fits your garage?

Two things point the way: how much sun reaches the floor and what the moisture test shows. Our polyurea base coat systems page explains both packages. We serve Polk County and the Four Corners side of Central Florida. For a free estimate on your own floor, call or text (866) 282-7667.

Frequently asked questions

Is polyaspartic the same as polyurea?
Polyaspartic is one kind of polyurea. A trade column calls it a polyaspartic aliphatic polyurea, and one data sheet describes it as an aliphatic polyurea coating. It reacts slower than spray polyurea, so it can go down by brush, squeegee or roller.
Does polyurea turn yellow in the sun?
Aromatic polyurea can. A paper from the polyurea trade association's conference says it will fade or change color in ultraviolet light. Aliphatic polyurea, which includes polyaspartic, has excellent resistance to UV breakdown. Both of our full broadcast packages finish with a clear polyaspartic topcoat.
Which is more flexible, polyurea or polyaspartic?
Polyurea, in the sheets we read. One coating maker lists 65 percent elongation for its polyurea flake system. Its polyaspartic flake system lists 10 percent on the same test. That maker says the polyurea system handles low to moderate movement and thermal cycling.
Can a garage floor really be coated in one day?
Some systems allow it on paper. A trade column puts a polyaspartic garage floor at about 5 hours, start to finish. The same column reports failures over slabs with too much moisture vapor. Ask for a moisture test, and ask when you can park on the floor.
Does humidity change how these coatings go down?
Yes. One polyaspartic sheet says it dries quicker, with less working time, when relative humidity is higher. One polyurea flake system sheet wants the slab at least 5 degrees Fahrenheit above the dew point. Both are reasons to check the slab and the air before the first coat.
How do I know if my slab has a moisture problem?
A moisture test tells you. Two methods are a calcium chloride test and in-slab relative humidity testing, and one polyurea system sheet recommends both. Each base coat has its own limit, so the reading gets compared with that product's sheet.
Is this what Armor Garage Flooring charges?
No. The dollar figures in this guide are market ranges from a national cost guide, not our price list. Your quote depends on your floor's size and condition and on what a moisture test shows. Call or text (866) 282-7667, and we will look at the floor and put your free estimate in writing.
Request a Quote

Get In Touch With Armor Garage Flooring

Tell us about the floor you want coated and where the property is. Call or text (866) 282-7667 or use the form, and we will set up your free estimate.

  • Call or text (866) 282-7667
  • Serving Eagle Lake, FL and the Lakeland and Winter Haven area
  • Free written estimates · garage, patio, driveway and shop floors

Request a Quote

Tell us about the garage, patio, driveway or shop floor and where it is. We look at the job and put your free estimate in writing.

Call (866) 282-7667